Wind Load Calculation per ASCE 7: Velocity Pressure, Gust Factor and Design Wind Pressure Worked Example
Wind often governs lateral design and roof uplift on steel industrial buildings, yet the ASCE 7 procedure is easy to misapply when editions mix. This post answers three common questions, then works an example for a steel-frame building. It extends our overview of structural engineering for industrial plants.
What is the formula for calculating wind load?
For a building, the design wind pressure on a surface is p = q G Cp − qi (GCpi), and the force is F = p × A, where A is the tributary area. The velocity pressure follows from wind velocity: qz = 0.00256 Kz Kzt Kd Ke V² in psf with V in mph, or qz = 0.613 Kz Kzt Kd Ke V² in N/m² with V in m/s. Kz is the height exposure coefficient, Kzt the topographic factor, Kd the wind directionality factor, Ke the ground elevation factor (ASCE 7-16 onward), G the gust factor (0.85 for rigid buildings) and Cp the external pressure coefficient.
The chain suits an Excel sheet: tabulate Kz by height, compute q, then apply Cp surface by surface. Wind direction matters, because the roof and walls are checked for wind from each principal direction. The uplift force on a roof truss or purlin is the net of external suction and internal pressure, reduced by dead load. Exposure B is urban or wooded terrain, C open terrain with scattered obstructions, and D flat coastal terrain. The Occupancy or Risk Category, I to IV, sets the importance factor in ASCE 7-05 and the wind speed map in ASCE 7-16.
Other codes follow the same logic: EN 1991-1-4 (Eurocode 1) uses a peak velocity pressure from a basic wind velocity, and NSCP 2015 follows the ASCE 7 approach with its own wind map. Confirm the adopted edition. On a steel structure, MWFRS pressures load the frame and C&C pressures load cladding and purlins.

How do I calculate wind load according to ASCE 7-05?
Use Chapter 6, Method 2 (analytical procedure), for regular buildings. The steps are:
- Take basic wind speed V from the map (Figure 6-1), a 3-second gust at 33 ft in Exposure C, and importance factor I from Table 6-1.
- Set the wind directionality factor Kd = 0.85 for buildings (Table 6-4), pick the exposure category, then read Kz (Table 6-3) and find Kzt.
- Classify enclosure: GCpi = ±0.18 for enclosed and ±0.55 for partially enclosed buildings.
- Compute qz = 0.00256 Kz Kzt Kd V² I, with qh at mean roof height.
- Use G = 0.85 for rigid buildings and take the external pressure coefficient Cp for walls and roof from Figure 6-6.
- Combine: p = q G Cp − qh (GCpi) for the main frame, and p = q [(GCp) − (GCpi)] for components and cladding.
Software such as ETABS can generate ASCE 7-05 wind loads on diaphragms, but check the exposure, enclosure and Cp inputs against a hand spreadsheet. Hip roofs have their own edge and corner coefficients in the components and cladding figures. For pipe and pipe racks, use force coefficients for open structures, as in our pipe rack load combinations post. ASCE/SEI 7-05 strength combinations use 1.6W, with 0.9D + 1.6W for wind uplift; allowable stress design uses 0.6D + W.
How is wind load calculated according to ASCE 7-16?
ASCE 7-16 organises wind in Chapters 26 to 31: general parameters (26), MWFRS directional procedure (27), envelope procedure for low-rise buildings (28), other structures (29), components and cladding (30) and wind tunnel (31). Main differences from ASCE 7-05:
- Importance factor removed; Risk Category now selects the map (Figure 26.5-1), with 300-, 700- and 1,700-year return periods for Risk Categories I, II and III/IV.
- Ground elevation factor Ke = exp(−0.0000362 zg), zg in ft, reduces q at altitude (about 0.83 at 5,000 ft).
- Velocity pressure coefficient Kz comes from Table 26.10-1 and Kd from Table 26.6-1; qz = 0.00256 Kz Kzt Kd Ke V² has no importance factor.
- Wind speeds are strength level, so load combinations change: LRFD uses 1.0W (uplift 0.9D + 1.0W) and ASD uses 0.6W (uplift 0.6D + 0.6W).
- Components and cladding: p = qh [(GCp) − (GCpi)], where GCp depends on effective wind area, so small areas such as fasteners and panels see higher suction. Effective wind area is span × effective width, not less than span²/3. Flat and hip roofs have separate edge and corner zones.
A full wind analysis checks every wind direction, torsional cases, and the minimum loads of 16 psf on walls and 8 psf on roofs. ASCE 7-22 keeps this framework, with updated maps, a new tornado chapter and revised solar panel provisions (array layout is in our solar panel row spacing post). Confirm the adopted edition.
Worked Example: Steel-Frame Industrial Building
Enclosed single-storey steel portal-frame building, 120 ft long in the wind direction and 60 ft wide, mean roof height h = 30 ft, roof slope below 10°, frames at 25 ft spacing, roof dead load 8 psf. ASCE 7-16: Risk Category II, V = 115 mph (51.4 m/s), Exposure C, Kzt = 1.0, Kd = 0.85, Ke = 1.0, rigid (G = 0.85), GCpi = ±0.18. Cp and GCp values are illustrative; confirm them against the code figures.
| Step | Calculation | Result |
|---|---|---|
| Kz at 30 ft | 2.01 (30/900)^(2/9.5) | 0.98 |
| Velocity pressure qh | 0.00256 × 0.98 × 1.0 × 0.85 × 1.0 × 115² | 28.2 psf (1.35 kPa) |
| Internal pressure | 28.2 × 0.18 | ±5.1 psf |
| Windward wall | 28.2 × 0.85 × 0.8 | +19.2 psf |
| Leeward wall (L/B = 2) | 28.2 × 0.85 × (−0.3) | −7.2 psf |
| Net frame pressure | 19.2 + 7.2 (internal cancels) | 26.4 psf |
| Frame lateral force | 26.4 × 30 ft × 25 ft | 19.8 kip |
| Average roof Cp | (30 × 0.9 + 30 × 0.5 + 60 × 0.3) / 120 | −0.50 |
| Net roof uplift | 28.2 × 0.85 × (−0.5) − 5.1 | −17.1 psf |
| Uplift combination 0.9D + 1.0W | 0.9 × 8 − 17.1 | −9.9 psf (14.9 kip per frame) |
| Wall cladding, zone 5, 10 ft², GCp = −1.4 | 28.2 × (−1.4 − 0.18) | −44.6 psf |
Windward and leeward walls give 26.4 psf, above the 16 psf minimum, so the frame takes about 19.8 kip of lateral wind force. Net roof uplift is 9.9 psf after 0.9D, which drives the anchor rods (see our column base plate design post). The zone 5 cladding pressure is much higher than MWFRS pressures, so cladding and fasteners are designed separately.
Practical Checks
- Confirm the edition adopted locally and verify all coefficients against the code.
- Determine exposure for each wind direction from the upwind terrain, and check Kzt on hills and ridges.
- Check enclosure: large openings or doors that may be open can make a building partially enclosed (GCpi = ±0.55).
- Use only dead load that is certain to be present for uplift.
- Compare software-generated loads with a hand check of qh and one wall pressure.
- Keep one labelled calculation spreadsheet per code edition, with units stated.
How Fluxiss Approaches Wind Loads
Fluxiss is a multidisciplinary engineering consultancy serving oil and gas, power and maritime clients. Its structural team checks wind loads on steel frames, pipe racks and equipment supports against the project's design code, and passes the reactions into foundation and connection design.
Frequently Asked Questions
What is the difference between MWFRS and C&C?
MWFRS pressures design the main frame, bracing and diaphragms; C&C pressures design cladding, purlins and fasteners for higher local suction.
Why is wind uplift often critical?
Light roofs have little dead load to resist suction, so connections and anchors govern.
Is 0.6W used with ASCE 7-05 wind speeds?
No. The 0.6 factor belongs to ASCE 7-10 and later, whose maps are strength level; ASCE 7-05 uses W with its own maps.
Can one spreadsheet cover every edition?
Not safely, because I, Ke and the load factors differ between editions.
Need help with wind loads on steel structures?
Fluxiss provides structural engineering for industrial plants, including wind load calculation, steel frame and pipe rack design, and connections. Send your drawings and site data, and the team can advise on the checks you need.
Comments
Post a Comment
Questions or corrections are welcome. Please mention the relevant section and units. Do not post confidential project data or personal contact details. For project inquiries, use the Fluxiss contact page.