Posts

Wind Load Calculation per ASCE 7: Velocity Pressure, Gust Factor and Design Wind Pressure Worked Example

Image
Wind often governs lateral design and roof uplift on steel industrial buildings, yet the ASCE 7 procedure is easy to misapply when editions mix. This post answers three common questions, then works an example for a steel-frame building. It extends our overview of structural engineering for industrial plants . Steel-frame building under construction. Photo: Dwight Burdette, CC BY 3.0, via Wikimedia Commons . What is the formula for calculating wind load? For a building, the design wind pressure on a surface is p = q G Cp − qi (GCpi), and the force is F = p × A, where A is the tributary area. The velocity pressure follows from wind velocity: qz = 0.00256 Kz Kzt Kd Ke V² in psf with V in mph, or qz = 0.613 Kz Kzt Kd Ke V² in N/m² with V in m/s. Kz is the height exposure coefficient, Kzt the topographic factor, Kd the wind directionality factor, Ke the ground elevation factor (ASCE 7-16 onward), G the gust factor (0.85 for rigid buildings) and Cp the external pressure coefficient. Th...

Pipe Expansion Loop Design Calculation: Thermal Growth, Loop Sizing and ASME B31.3 Worked Example

Image
Pipes grow when they heat up, and a line held between two anchors has nowhere to put that growth except into stress and anchor load. An expansion loop gives the movement somewhere to go. This post answers the five questions engineers search for most, then sizes a loop for a carbon steel steam line on a pipe rack using the thermal growth equation and the guided cantilever method. An expansion loop in an above-ground pipeline. Photo: Mick Garratt, CC BY-SA 2.0, via Wikimedia Commons . How do I calculate the size of an expansion loop for a pipe? Work in three steps. First find the thermal growth between anchors, then choose the leg length that absorbs it within the allowable stress range, then check the result in a pipe stress model. The same method applies to steam piping and other steel pipes; copper pipe and PVC or CPVC plastic pipe follow the same equations with different expansion coefficients, moduli and allowable stresses. Thermal growth: ΔL = α L ΔT Guided cantilever leg:...

Solar Panel Row Spacing Calculation: Inter-Row Shading, Tilt Angle and Ground Coverage Ratio Worked Example

Image
Row spacing is a trade between two losses: rows packed too tightly shade each other and cost energy, while rows spread too far apart waste land or roof area. The calculation is geometry plus one judgment, the design hour for which shading is accepted. This post answers the four questions people search for most about solar panel layout, then works through a full example at 40° north. It supports our wider guide to solar PV engineering design and yield . Rows of ground-mounted solar panels. Photo: Neil Owen, CC BY-SA 2.0, via Wikimedia Commons . How to calculate row spacing? Row spacing starts with the sun at the worst time you are willing to accept. For a south-facing array in the northern hemisphere, that is the winter solstice, with declination δ = −23.45°, at a design hour such as 9:00 and 15:00 solar time. The sun is lowest and the shadows longest then, so a layout that is clear at that hour is clear for the rest of the year at those times. The key equations are: Solar alt...

Pressure Vessel Shell Thickness Calculation: ASME VIII Div. 1 UG-27 Formula and Worked Example

Image
Shell thickness is the first number on a pressure vessel data sheet, and almost every other dimension follows from it: plate cost, weld volume, nozzle reinforcement and the weight on the foundation. ASME Section VIII Division 1 sets the rules through the UG-27 formulas, which apply to shells under internal pressure. This post answers the four questions engineers search for most, then works through a full example. It sits alongside our wider guide to pressure vessel and storage tank design . A pressure vessel used in industry. Photo: Exit2dos2000, CC BY-SA 3.0, via Wikimedia Commons . How to calculate shell thickness of pressure vessel? Start from thin-walled pressure vessel theory. Internal pressure P in a cylinder of radius R and wall t creates a hoop stress σ h = P R / t and a longitudinal stress of half that, σ L = P R / (2t). The radial stress, falling from −P inside to zero outside, is small by comparison and is neglected. Hoop stress is larger, so it normally sets the thic...

HVAC Duct Sizing by the Equal Friction Method: Velocity, Pressure Loss and Fan Static Pressure Worked Example

Image
Duct sizing looks simple on a drawing, yet it fixes three things at once: the fan energy the building will burn for decades, the noise at the diffusers, and the space the ducts take in the ceiling void. The equal friction method is the workhorse for low-velocity supply systems because it sizes every section at the same pressure loss per metre, so the design stays balanced without a full network solve. This post sets out the airflow, velocity and pressure loss basics, then sizes a small office supply system step by step and ends with the fan static pressure. It builds on our overview of MEP engineering design from load calculations to coordinated systems . Exposed spiral and rectangular supply ducts in a shopping mall: duct size sets velocity, noise and fan energy. Photo: W.carter, CC BY-SA 4.0, via Wikimedia Commons . Fundamentals of Duct Sizing Airflow comes from the sensible cooling load and the temperature difference between room and supply air. In SI, Q = Φ / (1.21 × ΔT), with...

ASME B31.3 Pipe Wall Thickness Calculation: Pressure Design, Corrosion Allowance and Mill Tolerance Worked Example

Image
Every piping line starts with a wall thickness. Choose it too thin and the pipe cannot hold the design pressure through its corrosion life; choose it too thick and the line becomes heavier, harder to support and more expensive to weld. ASME B31.3 gives a direct equation for the pressure design thickness of straight pipe, and the designer then adds allowances and mill tolerance to select a standard schedule. This post sets out that sequence and works through an 8 inch carbon steel example. It is the first step of the wider piping design and stress analysis workflow . Welded carbon steel gas pipeline: wall thickness is set by pressure design plus corrosion and mill tolerance allowances. Photo: Hamid Soufi, CC BY-SA 3.0, via Wikimedia Commons . Fundamentals of Pressure Design Thickness Internal pressure puts a hoop tension in the pipe wall, and the wall must be thick enough to keep that stress below the allowable value at the design temperature. Use the most severe coincident pressur...

Chilled Water Pipe Sizing: Velocity Limits, Friction Loss and Pump Head Worked Example

Image
Chilled water pipes are sized twice over: once for the flow they must carry, and again for the pumping energy they will cost over the life of the building. Pipe that is too small saves material but drives up friction loss, noise and pump power. Pipe that is too large costs more to buy, insulate and support. This post sets out the velocity and friction limits, the equations behind them, and a worked example that goes from a 600 kW cooling load to a pump duty point. It builds on our overview of MEP engineering design from load calculations to coordinated systems . Fundamentals of Chilled Water Pipe Sizing Flow follows from the cooling load and the temperature rise across the coils. A 6 K rise, typically 6 °C supply and 12 °C return, is common, and a larger rise cuts the flow and so the pipe size. Using 6 K instead of 5 K cuts the flow by about 17% for the same load. Water carries about 4.19 kJ per kg per kelvin, so the flow in litres per second is the load in kW divided by 4.19 times ...

Flange Leakage Check in Piping Stress Analysis: Kellogg Equivalent Pressure and ASME VIII Appendix 2 Worked Example

Image
A flange can pass every pipe stress check and still leak. The beam model reports bending moments and axial forces at a flange as ordinary pipe loads, never as a threat to the gasket. Yet those loads unload the gasket on one side of the joint, so a joint that was tight at hydrotest can weep in operation. This post explains the flange leakage check, sets out the Kellogg equivalent pressure method and the ASME VIII Division 1 Appendix 2 bolt load equations, and works through an NPS 8 example. It extends the piping design and stress analysis workflow into the joints themselves. Fundamentals: Why External Loads Make Flanges Leak A gasketed joint seals while gasket compressive stress stays above the level the gasket needs. Bolt preload provides it at assembly. In service, internal pressure acts on the gasket reaction diameter and tries to separate the faces, so the bolts must carry that end force and still leave a residual load on the gasket. External loads add to the pressure end force...